Here Many tutorials On the web for using mac install to Mac OS X Snow Leopard On your PC.may be unable to follow such tutorials if you do not readily have access to a Mac to perform the preparation necessary for the installation.Great progress has been made in hacking PCs to run OS X, and it is now possible to install Mac OS X without a Mac. Thanks to some great tools put together by some brilliant hackers, it is also much easier and does not involve nearly as much time and effort as was once required.
1. intel core i3-530 Clarkdale
2.4-pin To 8-pin Power Adapter
3.DVD Burner
4.585 Watt Power Supply
5.Micro ATX Computer Case
6. DDR3 4GB 1333 RAM
7. Gigabyte GA-H55M -USB 3 MOTHER BOARD.
Motherboard has an 8-pin power connector on it, and although it is possible to connect a single 4-pin connector to it, you may encounter odd issues running with just a single 4-pin connector. To ensure that you provide sufficient power to the board, you should purchase the 4-pin to 8-pin power adapter. Alternatively, you could purchase a power supply with 3x 4-pin connectors (1 for the 20+4-pin main connector, and 2 for the 8-pin connection) or an 8-pin connector.
purchase a hard drive or video card, as I used some I already had from another PC, but you will need those items as well. As of the time this article was written, you can get a 1TB drive shipped for $75 and an NVIDIA GeForce 9500 GT video card for $65.I also purchased v10.6.3 of OS X Snow Leopard retail DVD for a mere $29 (was about $35 with shipping & handling).All-in-all, the full system (without monitor) will run you around $600 (you could also add a 22″ monitor for $170).
You could certainly try doing it even cheaper with different hardware, but you’ll need to figure out the appropriate changes to make in the BIOS and boot loader installation.I did my best to put together a fairly modern system for a very reasonable price. Having used this set of hardware, I can affirm that it runs OS X Snow Leopard very well. Without a doubt, $600 – $800 is a far cry from what you would spend on an equivalent Mac from Apple. Granted it won’t be as compact or pretty as an iMac, but it will be just as functional.
successfully used both of them with my hardware setup. However I recommend you try iBoot first, as it is a bit leaner and doesn’t take as long to boot. If you’re using my hardware configuration, be sure to download the iBoot Supported disk image. If you use Empire EFI, download the Empire EFI v1.085 R2 image.
You can use one of many free programs to burn CDs if you don’t have one. Be sure to use the disk image burning mode in your CD burning software. Do not just simply copy the disk image file to a blank CD. I like Infra Recorder, because it makes this very easy. All you have to do is click the Write Image button, select the image, and burn it. Once again, you may wish to use rewritable media if you’re using a different hardware configuration than mine.
go to Advanced BIOS Features and set the First Boot Device toCDROM. I have my USB drive as the second drive and then Hard Disk as third – you can configure yours the same way if you wish to ever boot from a USB drive. Just be sure that Hard Disk is the Second Boot Device or Third Boot Device.
Next, configure SATA to run in AHCI mode in the Integrated Peripheralsmenu. You’ll need to set both PCH SATA Control Mode and Onboard SATA/IDE Ctrl Mode to AHCI.
Finally, go to Power Management Setup and set the HPET Mode to 64-bit mode.
Insert the Retail Mac OS X Snow Leopard DVD, wait a few seconds, and press F5.
When you see the screen below, select Mac OS X Install DVD should already be selected) and press Enter.
If all goes well, you should eventually see the language selection screen for the installer. If all did not go well and you do not make it to the language selection screen, try downloading a different version of iBoot or Empire EFI.
Select your disk drive.
Click Partition.
Select 1 Partition for the partition scheme. Note: If you have a drive that is larger than 2 TB, do not create partitions larger than 1 TB. Split the drive into multiple partitions, and be sure the main installation partition is 1 TB or smaller.
Enter a name for the partition (I used Hackintosh).
Select Mac OS Extended (Journaled) as the Format.
Click Options…, select GUID Partition Table, and then click OK.
Click Apply.
Quit Disk Utility and proceed with the installation. Install on the Hackintosh partition.
Do not fret when you reboot after the installation and get a boot error, as you will need to first boot the machine with iBoot (or Empire EFI). Eject the Mac OS X Snow Leopard install DVD, put your boot CD back into the drive, and reboot the machine. Now when you boot up, you should see a second choice for your installation partition (Hackintosh if you named it that way). Select the Hackintosh partition and press Enter to boot into OS X.
Once you’ve completed the first-run setup, open up Safari and download Multibeast. Multibeast is another superb tool by tonymacx86 and MacMan that makes it stupid easy to install the boot loader, along with all the drivers necessary for your Hackintosh to function properly.
In addition to downloading Multibeast, you will need to download the DSDT for the Gigabyte GA-H55M-USB3 and copy it to the desktop. Be sure to save.
. Launch Multibeast and make the following selections (your choices will differ if you have a different motherboard/hardware configuration):
After MultiBeast finishes installing, eject the iBoot CD and reboot the system. You should be able to boot right up from the hard drive, and all your devices should work just fine.Step 7: Getting Started with Your New Mac
you have any problems installing Mac OS X on your PC, just post a comment right here and we’ll do what we can to help. Just be sure to provide as much information about the hardware you’re using:
Motherboard make and model Gigabyte GA-H55M-USB3CPU model Intel Core i3-530
GPU model NVIDIA GeForce 9900 GT
I never managed to get sleep to work. When I try to put the computer to sleep, it sort of goes into a coma. The fans never shut down and the machine doesn’t wake up when you press the power button. If you manage to get sleep to work with my hardware configuration, please do feel free to share your solutions to Any One Techdebute Articles.
1.GETTING THE HARDWARE READY:
Hardware for the purposes of building a Hackintosh (often PCs running Mac OS X are referred to as such;1. intel core i3-530 Clarkdale
2.4-pin To 8-pin Power Adapter
3.DVD Burner
4.585 Watt Power Supply
5.Micro ATX Computer Case
6. DDR3 4GB 1333 RAM
7. Gigabyte GA-H55M -USB 3 MOTHER BOARD.
Motherboard has an 8-pin power connector on it, and although it is possible to connect a single 4-pin connector to it, you may encounter odd issues running with just a single 4-pin connector. To ensure that you provide sufficient power to the board, you should purchase the 4-pin to 8-pin power adapter. Alternatively, you could purchase a power supply with 3x 4-pin connectors (1 for the 20+4-pin main connector, and 2 for the 8-pin connection) or an 8-pin connector.
purchase a hard drive or video card, as I used some I already had from another PC, but you will need those items as well. As of the time this article was written, you can get a 1TB drive shipped for $75 and an NVIDIA GeForce 9500 GT video card for $65.I also purchased v10.6.3 of OS X Snow Leopard retail DVD for a mere $29 (was about $35 with shipping & handling).All-in-all, the full system (without monitor) will run you around $600 (you could also add a 22″ monitor for $170).
You could certainly try doing it even cheaper with different hardware, but you’ll need to figure out the appropriate changes to make in the BIOS and boot loader installation.I did my best to put together a fairly modern system for a very reasonable price. Having used this set of hardware, I can affirm that it runs OS X Snow Leopard very well. Without a doubt, $600 – $800 is a far cry from what you would spend on an equivalent Mac from Apple. Granted it won’t be as compact or pretty as an iMac, but it will be just as functional.
2.PREPARE THE BOOT DISK;
hardware and a retail copy of Mac OS X Snow Leopard, you’ll also need a blank CD. You may want to use a rewritable CD if you’re using a different hardware configuration, just in case the first one I recommend doesn’t work for you. There are two boot disk images that will allow you to install OS X directly from the installation DVD:successfully used both of them with my hardware setup. However I recommend you try iBoot first, as it is a bit leaner and doesn’t take as long to boot. If you’re using my hardware configuration, be sure to download the iBoot Supported disk image. If you use Empire EFI, download the Empire EFI v1.085 R2 image.
You can use one of many free programs to burn CDs if you don’t have one. Be sure to use the disk image burning mode in your CD burning software. Do not just simply copy the disk image file to a blank CD. I like Infra Recorder, because it makes this very easy. All you have to do is click the Write Image button, select the image, and burn it. Once again, you may wish to use rewritable media if you’re using a different hardware configuration than mine.
3.BIOS CONFIGURATION;
Fortunately, the Gigabyte GA-H55M-USB3 does not require a lot of configuration to run Mac OS X. When you first turn on or reboot the machine, press the delete key to enter the BIOS setup. You can just load the Optimized Defaults, and just make a few changes within three sections of the bios: Advanced BIOS Features, Integrated Peripherals, and Power Management Setup.go to Advanced BIOS Features and set the First Boot Device toCDROM. I have my USB drive as the second drive and then Hard Disk as third – you can configure yours the same way if you wish to ever boot from a USB drive. Just be sure that Hard Disk is the Second Boot Device or Third Boot Device.
Next, configure SATA to run in AHCI mode in the Integrated Peripheralsmenu. You’ll need to set both PCH SATA Control Mode and Onboard SATA/IDE Ctrl Mode to AHCI.
Finally, go to Power Management Setup and set the HPET Mode to 64-bit mode.
4. Installing Mac OS X
Insert the iBoot (or Empire EFI) boot disk.When you see screen below, eject the disk.
Insert the Retail Mac OS X Snow Leopard DVD, wait a few seconds, and press F5.
When you see the screen below, select Mac OS X Install DVD should already be selected) and press Enter.
If all goes well, you should eventually see the language selection screen for the installer. If all did not go well and you do not make it to the language selection screen, try downloading a different version of iBoot or Empire EFI.
Select your language and click the arrow to proceed.
Next, you need to partition your drive. Click on Utilities > Disk Utility.Select your disk drive.
Click Partition.
Select 1 Partition for the partition scheme. Note: If you have a drive that is larger than 2 TB, do not create partitions larger than 1 TB. Split the drive into multiple partitions, and be sure the main installation partition is 1 TB or smaller.
Enter a name for the partition (I used Hackintosh).
Select Mac OS Extended (Journaled) as the Format.
Click Options…, select GUID Partition Table, and then click OK.
Click Apply.
Quit Disk Utility and proceed with the installation. Install on the Hackintosh partition.
5. Installing the Boot Loader
Do not fret when you reboot after the installation and get a boot error, as you will need to first boot the machine with iBoot (or Empire EFI). Eject the Mac OS X Snow Leopard install DVD, put your boot CD back into the drive, and reboot the machine. Now when you boot up, you should see a second choice for your installation partition (Hackintosh if you named it that way). Select the Hackintosh partition and press Enter to boot into OS X.
Once you’ve completed the first-run setup, open up Safari and download Multibeast. Multibeast is another superb tool by tonymacx86 and MacMan that makes it stupid easy to install the boot loader, along with all the drivers necessary for your Hackintosh to function properly.
In addition to downloading Multibeast, you will need to download the DSDT for the Gigabyte GA-H55M-USB3 and copy it to the desktop. Be sure to save.
. Launch Multibeast and make the following selections (your choices will differ if you have a different motherboard/hardware configuration):
After MultiBeast finishes installing, eject the iBoot CD and reboot the system. You should be able to boot right up from the hard drive, and all your devices should work just fine.Step 7: Getting Started with Your New Mac
you have any problems installing Mac OS X on your PC, just post a comment right here and we’ll do what we can to help. Just be sure to provide as much information about the hardware you’re using:
Motherboard make and model Gigabyte GA-H55M-USB3CPU model Intel Core i3-530
GPU model NVIDIA GeForce 9900 GT
I never managed to get sleep to work. When I try to put the computer to sleep, it sort of goes into a coma. The fans never shut down and the machine doesn’t wake up when you press the power button. If you manage to get sleep to work with my hardware configuration, please do feel free to share your solutions to Any One Techdebute Articles.
EmoticonEmoticon